Were you looking for help and advice about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a tub isn't exactly rocket science, but it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is additionally a reasonably challenging task. If the old tub is readily obtainable, the job can move speedily; if you need to open a wall to remove the old bathtub as well as place the brand-new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's abilities, although you will certainly need a helper to vacate the old tub as well as embeded in the new one. Make certain you have actually certified yourself for the job as well as fit trying it. As opposed to hiring a specialist to take control of a halfway-completed task, it is far better to consider employing one before you start. Opportunities are you might require a specialist plumber to make tube links.
This post will help you install a new bath tub in your washroom if you have actually already bought a brand-new tub and do not require to alter the setup of your previous water pipes.
Your devices as well as product list need to consist of the following:
Planning for the Installation
To start with, the supporting structure provided with the bath should be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets system to prevent pressure on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be quite troublesome because of the restricted access that is usually the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any kind of old securing compound.
Before proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Setting up the Bath tub
Using the two wood boards under its feet, position the bathtub in the needed placement. The wood boards are useful in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and adjusting the feet on the tub up until the level reads level.
To set up taps, fit the bottom of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the water supply and also check all joints and also brand-new pipework for leaks as well as tighten them if required. Load the tub as well as likewise examine the overflow outlet and also the normal electrical outlet for leaks.
Lastly, deal with the bath paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the tub must wait till the bathtub has been utilized at the very least once as this will certainly settle it right into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin making sure that the washers remain in location between the faucet and the sink. Safeguard the tap in position with the maker provided backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous kind should be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to break an inflexible seal, causing the water to pass through the wall surface in between the bath as well as the tiling, leading to issues with wetness and also feasible leakages to the ceiling below.
You can select from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked newspaper or soft rope. Remember to always load the bathtub with water prior to securing, to allow for the motion experienced when the bathtub is in usage. The sealer can crack rather early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles utilizing water-resistant or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that entry about Installing A Bathtub while doing a search on the web. Are you aware of another person who is serious about the niche? Feel free to promote it. Many thanks for your time. Visit us again soon.
Try Here